chip ferrite bead for high current revision february 13, 2014 1 / 6 @ socay electronics co., ltd. 2014 specifications are subject to change without notice. please refer to www.socay.com for current information. scpb-s series socay electronics co., ltd. www.socay.com u combination of high frequency noise suppression with capability of handing high current u the current rating up to 6 a with low dcr u high current dc power lines u circuits where a stable ground in unavailable operating temperature range -40 ~ +125 o c storage condition less than 40 and 70% rh storage time 6 months(size:1005), 12 months(size:1608 above) soldering method reflow or wave soldering 1 series name 2 size code: the first two digitals : length(mm), the last two digitals : width(mm) 3 material code 4 impedance( ), 25% 5 fixed decimal point 6 rated current cod l=1000ma m=1500ma n=2000ma p=2500ma q=3000ma r=4000ma u=5000ma w=6000ma 8 packaging: p - embossed paper tape, 7" reel t - embossed plastic tape, 7" reel 7 soldering : green parts: s-soldering lead-free f- lead-free for whole chip general technical data part numbering f eatures applications scpb 1608 s 12 1 p p f ( 1 ) ( 2 ) ( 3 ) ( 4 ) ( 5 ) ( 6 ) ( 7 ) ( 8 ) e .g.: 600=60 ? , 121=120 ?
chip ferrite bead for high current revision february 13, 2014 2 / 6 @ socay electronics co., ltd. 2014 specifications are subject to change without notice. please refer to www.socay.com for current information. scpb-s series socay electronics co., ltd. www.socay.com scpb1005 series part number impedance ( ) 25% test freq. (mhz) dcr ( ) (max.) rated current (ma) scpb1005s100npf 10 100 0.09 2000 scpb1005s300npf 30 100 0.09 2000 scpb1005s600lpf 60 100 0.20 1000 scpb1005s121mpf 120 100 0.15 1500 scpb1608 series part number impedance ( ) 25% test freq. (mhz) dcr ( ) (max.) rated current (ma) scpb1608s300qpf 30 100 0.04 3000 scpb1608s600qpf 60 100 0.04 3000 scpb1608s800qpf 80 100 0.04 3000 scpb1608s121ppf 120 100 0.07 2500 scpb1608s221npf 220 100 0.09 2000 scpb1608s301npf 300 100 0.09 2000 scpb1608s451mpf 450 100 0.15 1500 scpb1608s471lpf 470 100 0.20 1000 scpb1608s601lpf 600 100 0.20 1000 scpb2012 series part number impedance ( ) 25% test freq. (mhz) dcr ( ) (max.) rated current (ma) scpb2012s310wpf 31 100 0.015 6000 SCPB2012S400RPF 40 100 0.03 4000 scpb2012s600qpf 60 100 0.04 3000 scpb2012s800upf 80 100 0.02 5000 scpb2012s121upf 120 100 0.02 5000 scpb2012s221qpf 220 100 0.04 3000 scpb2012s301npf 300 100 0.09 2000 scpb2012s331npf 330 100 0.09 2000 scpb2012s601npf 600 100 0.09 2000 electrical characteristics
chip ferrite bead for high current revision february 13, 2014 3 / 6 @ socay electronics co., ltd. 2014 specifications are subject to change without notice. please refer to www.socay.com for current information. scpb-s series socay electronics co., ltd. www.socay.com scpb3216 series part number impedance ( ) 25% test freq. (mhz) dcr ( ) (max.) rated current (ma) scpb3216s300wtf 30 100 0.015 6000 scpb3216s500wtf 50 100 0.015 6000 scpb3216s800rtf 80 100 0.03 4000 scpb3216s121wtf 120 100 0.015 6000 scpb3216s601ptf 600 100 0.07 2500 scpb3216s122ltf 1200 100 0.20 1000 scpb3225 series part number impedance ( ) 25% test freq. (mhz) dcr ( ) (max.) rated current (ma) scpb3225s600mtf 60 100 0.15 1500 scpb3225s102ntf 1000 100 0.09 2000 scpb4516 series part number impedance ( ) 25% test freq. (mhz) dcr ( ) (max.) rated current (ma) scpb4516s600wtf 60 100 0.015 6000 scpb4516s851mtf 850 100 0.15 1500 scpb4532 series part number impedance ( ) 25% test freq. (mhz) dcr ( ) (max.) rated current (ma) scpb4532s121wtf 120 100 0.015 6000 scpb4532s601qtf 600 50 0.04 3000 scpb4532s132qtf 1300 60 0.04 3000 test level 250 mv test instruments l hp4291b rf impedance / material analyzer l hp4338a/b milliohm meter l agilent 8720es s-parameter network analyzer l hp6632b system dc power supply ** for special part number which is not shown in the above table, please refer to appendix. electrical characteristics (continue)
chip ferrite bead for high current revision february 13, 2014 4 / 6 @ socay electronics co., ltd. 2014 specifications are subject to change without notice. please refer to www.socay.com for current information. scpb-s series socay electronics co., ltd. www.socay.com for lead free solder unit: mm symbol 1005 (eia 0402) 1608 (eia 0603) 2012 (eia 0805) 3216 (eia 1206) 3225 (eia 1210) 4516 (eia 1806) 4532 (eia 1812) l 1.00 0.10 1.60 0.15 2.00 0.20 3.20 0.20 3.20 0.20 4.50 0.25 4.50 0.25 w 0.50 0.10 0.80 0.15 1.25 0.20 1.60 0.20 2.50 0.20 1.60 0.20 3.20 0.25 t 0.50 0.10 0.80 0.15 0.90 0.20 1.10 0.20 1.30 0.20 1.0 0.20 1.50 0.25 e 0.25 0.10 0.30 0.20 0.50 0.30 0.50 0.30 0.50 0.30 0.60 0.40 0.60 0.40 unit: mm size a b c 1005 0.40~0.60 1.60~2.60 0.40~0.70 1608 0.50~0.70 2.10~3.10 0.65~0.95 2012 1.00~1.20 3.00~4.00 0.80~1.10 3216 2.00~2.40 4.20~5.20 1.00~1.40 3225 2.10~2.30 4.20~5.20 2.20~2.50 4516 3.40~3.70 6.30~7.30 1.30~1.70 4532 3.40~3.70 6.30~7.30 2.90~3.20 construction & dimensions recommended soldering conditions 25 150 200 217 260 pre-heating soldering 60~120 second 30 second 60~150 second time (sec.) temperature () l t e e w recommended pad layout
chip ferrite bead for high current revision february 13, 2014 5 / 6 @ socay electronics co., ltd. 2014 specifications are subject to change without notice. please refer to www.socay.com for current information. scpb-s series socay electronics co., ltd. www.socay.com unit: mm symbol 1005 1608 2012 3216 3225 4516 4532 paper paper paper plastic plastic plastic plastic w 8.00 0.10 8.00 0.10 8.00 0.10 7.90~8.30 7.90~8.30 11.7~12.3 12.00 0.10 p 2.00 0.05 4.00 0.10 4.00 0.10 4.00 0.10 4.00 0.10 4.00 0.10 8.00 0.10 e 1.75 0.05 1.75 0.10 1.75 0.10 1.75 0.10 1.75 0.10 1.75 0.10 1.75 0.10 f 3.50 0.05 3.50 0.10 3.50 0.10 3.50 0.05 3.50 0.05 5.50 0.05 5.50 0.05 d 1.55 0.05 1.56 0.10 1.56 0.10 1.55 0.05 1.55 0.05 1.55 0.05 1.55 0.05 d1 na na na 0.95~1.20 0.95~1.20 1.50~1.75 1.50~1.75 p 4.00 0.10 4.00 0.10 4.00 0.10 4.00 0.10 4.00 0.10 4.00 0.10 4.00 0.10 p 0 10 na na 40.0 0.20 40.0 0.20 40.0 0.20 40.0 0.20 40.0 0.20 p2 2.00 0.05 2.00 0.10 2.00 0.10 2.00 0.05 2.00 0.05 2.00 0.05 2.00 0.05 a0 0.62 0.03 1.05 0.05 1.50 0.05 1.85 0.10 2.57 0.10 1.83 0.10 3.66 0.10 b0 1.12 0.03 1.85 0.05 2.30 0.05 3.43 0.10 3.40 0.10 4.85 0.10 4.95 0.10 k0(t) 0.60 0.03 0.95 0.05 0.95 0.05 1.22 0.10 1.32 0.10 1.83 0.10 1.83 0.10 t na na na 0.25 0.10 0.25 0.10 0.29 0.10 0.23 0.10 tape specifications plastic carrier direction of feed paper carrier
chip ferrite bead for high current revision february 13, 2014 6 / 6 @ socay electronics co., ltd. 2014 specifications are subject to change without notice. please refer to www.socay.com for current information. scpb-s series socay electronics co., ltd. www.socay.com unit: mm part size(eia size) packaging option quantity 1005 (0402) 7 reel 10,000 1608 (0603) 7 reel 4,000 2012 (0805) 7 reel 4,000 3216 (1206) 7 reel 3,000 3225 (1210) 7 reel 2,000 4516 (1806) 7 reel 2,000 4532 (1812) 7 reel 1,000 the contents of a box 1005 (0402): 6 reels / inner box 1608 (0603): 6 reels / inner box 2012 (0805): 6 reels / inner box 3216 (1206): 6 reels / inner box 3225 (1210): 6 reels / inner box 4516 (1806): 4 reels / inner box 4532 (1812): 4 reels / inner box test item test condition criteria temperature cycle a. temperature : -40 ~ +85 b. cycle : 100 cycles c. dwell time : 30minutes measurement : at ambient temperature 24 hrs after test completion a. no mechanical damage b. induction value should be within 20 % of the initial value operational life a. temperature : 125 5 b. test time : 1000 hrs c. apply current : full rated current measurement : at ambient temperature 24 hrs after test completion a. no mechanical damage b. induction value should be within 20 % of the initial value biased humidity a. temperature : 40 2 b. humidity : 90 ~ 95 % rh c. test time : 1000 hrs d. apply current : full rated current measurement : at ambient temperature 24 hrs after test completion a. no mechanical damage b. induction value should be within 20 % of the initial value resistance to solder heat a. solder temperature : 260 5 b. flux : rosin c. dip time : 10 1 sec a. more than 95 % of terminal electrode should be covered with new solder b. no mechanical damage c. induction value should be within 20 % of the initial value adhesive test a. reflow temperature : 245 it shall be soldered on the substrate applying direction parallel to the substrate b. apply force(f) : 5 n test time : 10 sec a. no mechanical damage b. soldering the products on pcb after the pulling test force > 5 n rated current test a. apply current : full rated current / 5min temperature rise should be less than 25 steam aging test a. temperature : 93 b. test time : 4hrs others: 8hrs c. solder temperature : 235 5 d. flux : rosin e. dip time : 5 1 sec more than 95 % of terminal electrode should be covered with new solder reel specifications & packaging reliability and test condition
|
